Four digit codes for GE Universal remote controls
- Ge 25008 Remote Code List
- Ge Universal Remote 25008 Manual
- Ge 25008 Universal Remote Control Manual
- Ge 25008 Universal Remote
- Ge 25008 Code List
- Ge 25008 Universal Remote Control Codes
Direct Code Entry for GE remotes with 4 digit codes
The following is a short tutorial on programming most models of GE universal remotes with 4 digit codes. See also this page for general GE remote code entering instructions.
Press and release the chosen device button (e.g., tv, cbl, dvd, aud). Enter the first 4-digit code for your device. The red light will turn off.
View and Download GE 25008 instruction manual online. Universal Remote Instruction Manual. 25008 remote control pdf manual download. Ge 25008 Pdf User Manuals. View online or download Ge 25008 Instruction Manual. Here is the list with ALL of the device codes for GE remotes 3 Digit Universal Remote Control Code List For GE Remote Controls ABEX 185, 172 ACME 003, 010, 021, 039, 049, 050 ADA 018, 025, 004, 007, 016 ADC 001, 002, 004, 005, 003, 009 ADMIRAL 001, 173, 020, 226 ADVENT 176, 899 GE.
Step 1: Press and hold the 'SETUP' button until the indicator light turns on, then release.
Step 2: Press and release the desired Mode button (TV, DVD, CBL/SAT, etc.). The indicator light will blink, then stays lit.
Step 3: Enter the 4 digit code for your device. After a valid code entry, the indicator light turns off. For an invalid code, the indicator light flashes.
Step 4: With your device on, test a few common functions like 'CHANNEL Up/Down' or 'VOLUME Up/Down' , 'MUTE', etc. If the device responds, no further programming is required. If some buttons don't work as they should, try a different code listed for your brand.
NOTE: The indicator light will either be a small red LED at the top of the remote or the illuminated 'ON/OFF' button.
About codes used in GE/Jasco remotes
There were multiple 4 digit code versions used in GE remotes over time, from V1 (2006), V2 (2011), V3, V4 (2012), V5, CL3 (2013), CL4 (2016) to the newest CL5 (2019).
To find out the version your remote uses, open the battery compartment, remove the batteries and locate the sticker containing the model number. A Version 2 through Version 5 remote will have a 'V2' to 'V5' after the model number. Older remotes with no version after the model# use the V1 code list. The newest ones will be CL3, CL4 or CL5.
In order to save you the hassle of going through multiple code tables, we have compiled together the code lists from different versions of GE remotes sharing the same code base (e.g. V2&V4, V3&V5). If your remote is slightly old, you'll get the benefit of finding the code for your device even if it appeared after your remote was manufactured, but uses an old code that already exists preprogrammed in your model. You can also find the code for some old devices that are dropped from the code lists, but still supported by newer remote controls. The only downside of this approach is, that there will be a few codes that are only supported by a particular version. So, if a code listed for your brand is not supported by your remote, try the next one from the list.
Sometimes a code will be accepted, but only allow limited function control (e.g. only volume and channel control). In this case, continue programming using the next code number for that brand.
Auto Code Search (for newer models)
The Auto Code Search searches automatically through all of the codes stored in your remote. If your device does not respond to any of the codes listed for your device, or your brand does not appear in the code lists, try the following steps:
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the indicator light stays on, then release.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, etc.). The indicator light will blink once and then remain on.
Step 4: With the remote pointed at the device, press and release the 'POWER' button on the remote once. Wait patiently until the remote sends a batch of 10 codes to the device. The indicator light will blink once for each code and remain on after sending the 10 codes. Repeat this step again and again until your device turns off.
Step 5: When the device turns off, manually turn the device back on.
Step 6: With the remote pointed at the device, press and release the 'VOL+' button until the device turns off. The remote will resend the last 10 codes one by one. Be sure to wait approximately 3 seconds after each 'VOL+' button press to allow the device time to respond.
Step 7: When the device turns off, press and release the same device button you pressed in Step 3 to store the code.
Notes:
- The 'VOL–' button can be used to go backwards through each batch of 10 codes.
- The indicator light will flash 2 times after testing the first or last code in each batch of 10.
- Test the buttons on the remote to see if the device responds as you would expect. If not all buttons work as they should, repeat this process to search for a better code.
- Repeat this process for each device you wish to control.
Auto Code Search (for older models)
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the red indicator light stays on (around 4 seconds) and then release the button.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, DVR/AUX). The red indicator will blink once and remains on.
Step 4: Point the remote at the device and press and release the 'POWER' button (for TV) or 'PLAY' button (for DVD, VCR, etc.) to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches. The remote must be pointed at your device for the entire duration of this search.
Step 5: Place your finger on the #1 button so you are prepared to lock-in the code.
Step 6: When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock-in the code.
Step 7: Point the remote at your device and check to see if the remote operates it as desired. If it does, no further programming is required. If it does not, return to step 2 and start the auto search again.
Ge 25008 Remote Code List
Code Search instructions for some older GE remotes
Step 1: Manually turn on the device to be controlled.
Step 2: Press and hold the 'SETUP' button until the red indicator stays on, then release.
Step 3: Press and release the desired Mode button (VCR, TV etc.). The red indicator will blink once, then stays on.
Step 4: Press the 'POWER' (or 'CHANNEL UP' for some versions) button repeatedly until the device to be controlled powers off (or changes channel). The red indicator will blink with each keypress. When all codes have been searched the red indicator flashes rapidly for 3 seconds.
Step 5: Press and release 'ENTER' (or 'MUTE' or 'SAVE') button to install the code. The indicator light goes off.
Generally it's best to store VCR codes under the VCR button, cable codes under CBL, and so on. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter any VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
GE Universal remote controls - programming instructions
How to Program a GE/Jasco Universal Remote Control
To find out the code(s) compatible with your device, see the GE remote control code lists for 3 digit or 4 digit GE remotes, or search for it here.
How to enter codes manually:
Step 1: Turn on the device (TV, DVD, VCR, Satellite receiver etc.) you wish to control.
Step 2: Press and hold the 'CODE SEARCH' or 'SETUP' button on the remote until the indicator light turns on, then release.
Step 3: Press and release the button for the device you are programming (TV, DVD, VCR, etc.). For AUX, press AUX button, then the device button you are assigning to AUX. The indicator light will blink then remain lit.
Ge Universal Remote 25008 Manual
Step 4: Enter the 3 or 4 digit code using the number buttons. After the code is entered the indicator light will turn off.
Step 5: Aim the remote at the device you want to control and press the 'POWER' button. Your device should turn off. If your equipment does not respond to the first code listed for your brand, repeat the code entry procedure with the next code. If the device turns off/on and responds correctly to common functions like Volume Up/Down or Program Up/Down, no further programming is required.
Notes:
- The indicator light will either be a small LED at the top of the remote or the illuminated 'ON/OFF' button.
- If none of the codes listed for your brand work or your brand does not appear in the code lists, instruct your remote to perform a code search.
Auto Code Search (for newer models)
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the indicator light stays on, then release.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, etc.). The indicator light will blink once and then remain on.
Step 4: With the remote pointed at the device, press and release the 'POWER' button on the remote once. Wait patiently until the remote sends a batch of 10 codes to the device. The indicator light will blink once for each code and remain on after sending the 10 codes. Repeat this step again and again until your device turns off.
Step 5: When the device turns off, manually turn the device back on.
Step 6: With the remote pointed at the device, press and release the 'VOL+' button until the device turns off. The remote will resend the last 10 codes one by one. Be sure to wait approximately 3 seconds after each 'VOL+' button press to allow the device time to respond.
Step 7: When the device turns off, press and release the same device button you pressed in Step 3 to store the code.
Notes:
- The 'VOL–' button can be used to go backwards through each batch of 10 codes.
- The indicator light will flash 2 times after testing the first or last code in each batch of 10.
- Test the buttons on the remote to see if the device responds as you would expect. If not all buttons work as they should, repeat this process to search for a better code.
- Repeat this process for each device you wish to control.
Auto Code Search (for older models)
Step 1: Manually turn on the device you wish to control.
Step 7: When the device turns off, press and release the same device button you pressed in Step 3 to store the code.
Notes:
- The 'VOL–' button can be used to go backwards through each batch of 10 codes.
- The indicator light will flash 2 times after testing the first or last code in each batch of 10.
- Test the buttons on the remote to see if the device responds as you would expect. If not all buttons work as they should, repeat this process to search for a better code.
- Repeat this process for each device you wish to control.
Auto Code Search (for older models)
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the red indicator light stays on (around 4 seconds) and then release the button.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, DVR/AUX). The red indicator will blink once and remains on.
Step 4: Point the remote at the device and press and release the 'POWER' button (for TV) or 'PLAY' button (for DVD, VCR, etc.) to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches. The remote must be pointed at your device for the entire duration of this search.
Step 5: Place your finger on the #1 button so you are prepared to lock-in the code.
Step 6: When the device shuts off or begins playing, press the #1 button to lock-in the code. The red indicator light will turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock-in the code.
Step 7: Point the remote at your device and check to see if the remote operates it as desired. If it does, no further programming is required. If it does not, return to step 2 and start the auto search again.
Ge 25008 Remote Code List
Code Search instructions for some older GE remotes
Step 1: Manually turn on the device to be controlled.
Step 2: Press and hold the 'SETUP' button until the red indicator stays on, then release.
Step 3: Press and release the desired Mode button (VCR, TV etc.). The red indicator will blink once, then stays on.
Step 4: Press the 'POWER' (or 'CHANNEL UP' for some versions) button repeatedly until the device to be controlled powers off (or changes channel). The red indicator will blink with each keypress. When all codes have been searched the red indicator flashes rapidly for 3 seconds.
Step 5: Press and release 'ENTER' (or 'MUTE' or 'SAVE') button to install the code. The indicator light goes off.
Generally it's best to store VCR codes under the VCR button, cable codes under CBL, and so on. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter any VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
GE Universal remote controls - programming instructions
How to Program a GE/Jasco Universal Remote Control
To find out the code(s) compatible with your device, see the GE remote control code lists for 3 digit or 4 digit GE remotes, or search for it here.
How to enter codes manually:
Step 1: Turn on the device (TV, DVD, VCR, Satellite receiver etc.) you wish to control.
Step 2: Press and hold the 'CODE SEARCH' or 'SETUP' button on the remote until the indicator light turns on, then release.
Step 3: Press and release the button for the device you are programming (TV, DVD, VCR, etc.). For AUX, press AUX button, then the device button you are assigning to AUX. The indicator light will blink then remain lit.
Ge Universal Remote 25008 Manual
Step 4: Enter the 3 or 4 digit code using the number buttons. After the code is entered the indicator light will turn off.
Step 5: Aim the remote at the device you want to control and press the 'POWER' button. Your device should turn off. If your equipment does not respond to the first code listed for your brand, repeat the code entry procedure with the next code. If the device turns off/on and responds correctly to common functions like Volume Up/Down or Program Up/Down, no further programming is required.
Notes:
- The indicator light will either be a small LED at the top of the remote or the illuminated 'ON/OFF' button.
- If none of the codes listed for your brand work or your brand does not appear in the code lists, instruct your remote to perform a code search.
Auto Code Search (for newer models)
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the indicator light stays on, then release.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, etc.). The indicator light will blink once and then remain on.
Step 4: With the remote pointed at the device, press and release the 'POWER' button on the remote once. Wait patiently until the remote sends a batch of 10 codes to the device. The indicator light will blink once for each code and remain on after sending the 10 codes. Repeat this step again and again until your device turns off.
Step 5: When the device turns off, manually turn the device back on.
Step 6: With the remote pointed at the device, press and release the 'VOL+' button until the device turns off. The remote will resend the last 10 codes one by one. Be sure to wait approximately 3 seconds after each 'VOL+' button press to allow the device time to respond.
Step 7: When the device turns off, press and release the same device button you pressed in Step 3 to store the code.
Notes:
- The 'VOL–' button can be used to go backwards through each batch of 10 codes.
- The indicator light will flash 2 times after testing the first or last code in each batch of 10.
- Test the buttons on the remote to see if the device responds as you would expect. If not all buttons work as they should, repeat this process to search for a better code.
- Repeat this process for each device you wish to control.
Auto Code Search (for older models)
Step 1: Manually turn on the device you wish to control.
Step 2: Press and hold the 'SETUP' button until the indicator light stays on, then release.
Step 3: Press and release the desired device button on the remote (TV, DVD, CBL/SAT, etc.). The indicator light will blink once and then remain on.
Step 4: Point the remote at the device and press and release the 'POWER' button (for TV) or 'PLAY' button (for DVD, VCR, etc.) to start the search. The indicator light will flash (approximately every 2 seconds) as the remote searches. Note: the remote must be pointed at your device for the whole duration of this search!
Step 5: Place your finger on the #1 button so you are prepared to lock-in the code.
Step 6: When the device shuts off or begins playing, press the #1 button to lock-in the code. The indicator light will turn off. Note: You have approximately 2 seconds after the device shuts off or begins playing to lock-in the code.
Step 7: Point the remote at the device and check if the remote operates the device as desired. If it does, no further programming is required. If it does not, return to step 2 and start the auto search again.
The Manual Code Search Method (for some older remotes)
Step 1: Turn on the equipment you wish to control.
Step 2: Press and hold 'CODE SEARCH' or 'SETUP' until the light turns on, then release.
Ge 25008 Universal Remote Control Manual
Step 3: Press and release the button for the device you are programming (VCR, DVD, TV etc.). The indicator light will blink once, then remain lit. For AUX, press AUX then the device button you are assigning to AUX.
Ge 25008 Universal Remote
Step 4: Press and release the 'POWER' button repeatedly until your device turns off. Wait at least two seconds between each time you press 'POWER'. Note that you may have to press 'POWER' up to 250 times!
Step 5: When your device turns off press the 'ENTER' or 'SAVE' button. The indicator light will turn off. Check other functions to see if your code is correct.
The SLEEP feature
Some GE remote controls like the RM94902, RM94904 or RM94905 have a handy 'sleep feature' enabling you to turn off your TV after a preprogrammed time interval of 1 to 99 minutes. To use the sleep feature follow these steps:
Ge 25008 Code List
1: Press and hold the 'SLEEP' button until the indicator light turns on.
2: Enter the time interval in minutes using the numerical keypad. (for minutes from 1 to 9 press 0 before the actual number).
3: Leave the remote aimed at the television set.
Ge 25008 Universal Remote Control Codes
To turn off the sleep feature, press and hold 'SLEEP' until the indicator light blinks or press the 'POWER' button to turn off the TV.
